Tuesday, April 4, 2017

Creator 31058 Mighty Dinosaurs Alternate MOC with instructions!





24/11/2017 Updates!  An error have been found and corrected for the legs instructions!

When I first set my eyes on this set last year, I just knew it will not disappoint! Many AFOLs attempted to MOC alternate creations from this set with great result the last few months. I admit that I was late to this party, only started to unbox it about a month ago.



This set reminds me  of one Creator Set 31032 from few years ago where I MOCed a Transformer from , Infernus ( building instructions inside!).


I'm not so sure what I shall name this vehicle. Perhaps its a hovercar of some sort.



Transform!

The number of hinged parts are just adequate  enough for me to get to work. Suprisingly.... it took me just a day to crank this one out. (and a few hours more later of the month to refine it). 




Robot Mode 





Scarcity of parts means I must make do with compromising building techniques. The hinged part located between his thighs is one fine example . I'm torn between keeping the socket part or removing it altogether , revealing the ball ummmm receptable.






This is no camera trick! He actually can stand on one foot.


I'm sorry dude! Ran out of parts to make you a weapon. You'll just have to pose barehanded.





Incoming Building Instructions!

I spent a while trying to optimize the number of steps and ended up with a small bunch of images below. Enjoy!!

Both Arms



Head

Left Leg




Right Leg



Body



Final Merging

I hope you enjoy building this guy as much as I did! Thanks for all the support !! =)

  • More free building instructions  (mostly from official LEGO sets)
  • Free building instructions for set  31058 
    • at

    20 comments:

    1. UnknownMay 20, 2017 at 4:22 PM

      Ok, I built the 31058 Transformer! Does this guy have an official name?

      Overall instructions were pretty easy to follow. Only one thing, I noticed for each leg, it shows construction using 3 2x1 light green pieces. Since there are only 4 total, 2 of these have to be dark green 2x1. I noticed in the final models, one of the lower legs uses the dark green 2x1s so I was able to figure it out.

      These transformers are so fun to build. This is the 2nd one of yours I have built from the Creator sets. I find your designs are better than the official Lego models.

      If your Transformers were available as official sets I would totally buy them. I really hope Lego will partner with you to make your Transformers official sets.

      Thanks for sharing these with us!

      ReplyDelete
      Replies
      1. AnonymousMarch 10, 2021 at 11:38 AM

        i don't think that thing has a name! But i'm gonna build it! Wish me luck!

        Delete
    2. UnknownOctober 13, 2017 at 11:50 AM

      I have a weapon design for him.

      ReplyDelete
    3. UnknownOctober 13, 2017 at 11:57 AM

      I can't put a picture on, sorry

      ReplyDelete
    4. UnknownOctober 13, 2017 at 1:16 PM

      I can tell you the instructions though. First, put a 1x2 1 clip plate on one stud on a 1x2 plate. Then, put a second 1x2 plate on the clip plate. Then, put a 1x2 1 bar plate on the second 1x2 plate. Then, put one of the white tubes with a clip on the bar plate. Then, put a normal sized bar in the tube clips tube. Then, put a 1x2 S.N.O.T brick with 4 side studs (two on each side) on the remaining stud on the first 1x2 plate. Then, put a 1x4 tile on the S.N.O.T brick and the bar plate. Then put a black technic pin in the remaining hole on the bottom of the S.N.O.T brick. And you have a blaster!

      ReplyDelete
    5. UnknownDecember 23, 2017 at 6:04 PM

      This comment has been removed by the author.

      ReplyDelete
    6. winxmasterMarch 25, 2019 at 2:02 PM

      i will call this guy quick charger i plan to get this set just to build this model

      ReplyDelete
    7. AnonymousJuly 10, 2019 at 4:10 PM

      Matthew Bobby,
      What is a S.N.O.T brick?

      ReplyDelete
    8. AnonymousJuly 10, 2019 at 5:30 PM

      Alan,
      What is this guys name? I didn't catch it.

      ReplyDelete
      Replies
      1. bumblebee1814September 21, 2019 at 11:49 PM

        this guy doesn't have a name i guess call him what you like

        Delete
    9. bumblebee1814September 21, 2019 at 11:01 PM

      This comment has been removed by the author.

      ReplyDelete
    10. bumblebee1814September 21, 2019 at 11:39 PM

      This comment has been removed by the author.

      ReplyDelete
    11. bumblebee1814September 21, 2019 at 11:47 PM

      i've built this guy before so i built him again because he's that good

      ReplyDelete
    12. JosieMay 8, 2020 at 2:03 AM

      This is the creator set I've been looking for for a long time, thanks for the great article

      ReplyDelete
    13. Suleforger ProductionsJuly 30, 2020 at 12:07 AM

      His alt mode reminds me more of a armed hoverboat then a hovercar.but its ausome anyway, i also have that set but made a diffrent Moc out of that( a fan made one)

      ReplyDelete
    14. Suleforger ProductionsJuly 30, 2020 at 6:18 AM

      I can show my moc from this set from the link
      https://suleforger.blogspot.com/2020/07/dragster-part-1-of-5.html
      and see it

      ReplyDelete
    15. AnonymousAugust 24, 2020 at 1:58 PM

      I cant find the post

      ReplyDelete
    16. AnonymousMarch 16, 2021 at 11:30 AM

      I wanna build this.

      ReplyDelete
    17. DinoJuly 24, 2021 at 6:07 AM

      It's a really cool build , I will call him Hovermech

      ReplyDelete